Caterclad®
Caterclad®
Developed in conjunction with Senior Environmental Health Officers, Caterclad® is the wall finish you can be sure is proven safe and hygienic, where it counts the most – where food is prepared or provided. That is why Caterclad® is a popular choice in hotels and restaurants, schools, hospitals and food processing plants.
Caterclad® conforms to EU and UK requirements in respect of wall finishes in food environments. Caterclad® is the only PVC hygienic wall lining system that has the EU Reports PrEN 13823 exposure to thermal attack and PrEN ISO 11925-2: 1999 direct impingement of flame.
Caterclad® has Warrington Fire Research Centre Reports confirming a pass in both BS476 Part 6 – Fire Propagation – and BS476 Part 7 – Surface Spread of Flame. Caterclad® also complies with Paragraph A12(b) of Approved Document B, Fire Safety in Building Regulations 1991.
The impervious finish only requires a wash down with hot water and sanitiser for it to be hygienic, clean and at the same time retain appearance
Technical Specification
Sheet dimensions | 2500 X 1220 x 2.5mm and 3050 X 1220 x 2.5mm |
Surface spread of flame | BS476 Part 7 1997 Class 1 |
Impact strength izod notch hardness | 2.1 |
Co-efficient of thermal expansion | 3.7 x 10-5 |
Specific gravity | 1.4 |
Thermal conductivity | 1.05 |
Maximum service temperature | 65°C |
Elastic modulus at bend | 4.5 x 10-3 |
Colour | Matt White |
Caterclad® Certification
PrEN 13823 exposure to thermal attack – Warres 116582 (EU Test)
PrEN ISO 11925-2 1999 direct impingement of flame – Warres 116603 (EU Test)
BS 476: Part 7: 1997 Surface Spread of Flame Class 1 Warres 102778
BS 476: Part 6: 1989 Fire Propagation Pass Warres 102779
Compliance as defined in Paragraph A12(b) of Approved
Document B, ‘Fire Safety’ in Buildings Regulations 1991
EEC Commission Directive 90/128/EEC Food Contact Safe Plastic
SGS Certification CP43044/BW/98
Lloyds Register of Shipping Certification SAS F020203/A1 for Marine & Off-Shore use
Architectural Specification
Supply and install Caterclad® to a finished height or Colour Match heat welded joints using Cladfix® panel adhesive; thermoformed internal and external corners with Cladfix® Co-extrusions between panels. Provide an Interclad® Assurance on completion.
Caterclad®/Mediclad® | m2 |
Caterclad®/Mediclad® (less than 300mm) | m |
Thermoformed internal/external corners | m |
Waterproof sealant at abutments | m |
Cutouts for service | No |
Standard Trims
Panel Joint (H) 2.5m/3.0m
End Stop (J) 2.5m/3.0m
External Corner (F) 2.5m/3.0m
Modified Panel Joint 2.5m only
Standard Trim Dimensions
Panel Joint (H)
End Stop (J)
External Corner (F)
The information on this site is to the best of our knowledge accurate and true. We are unable to accept responsibility in respect of factors which are outside our knowledge and control. In keeping with Interclad®’s policy of continuous product development specifications may change without notice. Changes will only improve the specification of our products. Products can be selected to help meet guidelines of Approved Document M (ADM) and the Equality Act (DDA).
Caterclad® Waterfield® Interclad® Cladfix® Mediclad® Interlock™ Softwall™ SuperBond™ are Trade Marks of Interclad® Limited.
The information on this site is to the best of our knowledge accurate and true. We are unable to accept responsibility in respect of factors which are outside our knowledge and control. In keeping with Interclad®’s policy of continuous product development specifications may change without notice. Changes will only improve the specification of our products. Products can be selected to help meet guidelines of Approved Document M (ADM) and the Equality Act (DDA).
Caterclad® Waterfield® Interclad® Cladfix® Mediclad® Interlock™ Softwall™ SuperBond™ are Trade Marks of Interclad® Limited.